How do I power up the radio transmitter at the castle?

3 Answers
  1. Build a small generator (skip if you have an existing with spare power)
  2. While in workshop mode still, press SPACE (Y on XB, Triangle on PS4) while highlighting the generator. (
  3. Highlight the Radio Tower, and press SPACE (Y on XB, Triangle on PS4) again.

Watch out a lot more about it. Hereof, how do you connect the generator to the radio in Fallout 4?

You will need to press the touchpad on the controller and highlight the generator and press the triangle button to attach wire, then move highlight the recruitment radio beacon and press the triangle button to attach the wire.

Additionally, how do you complete the old guns in Fallout 4? Quest objectives:

Also, how much power is needed at the Castle Fallout 4?

How do you gain access to the castle’s armory?

All you need to do is bring up the Workshop interface, and scrap the rubble into concrete. Doing this will clear the path to a tunnel leading down to the armory. To remove this rubble, open the Workshop menu and scrap the rubble for concrete.

How do I start independence in Fallout 4?

You should receive the chance to start this quest after completing few main and minor (random) quests for Minutemen. During the conversation with Preston Garvey in the Sanctuary, he will ask for your help in reclaiming the Castle that was the main quarter of the Minutemen in the past.

How do you find aluminum in Fallout 4?

Locations
  1. Two to four pieces of aluminum can be obtained from destroyed sentry bots and assaultrons.
  2. Sold by Arturo Rodriguez in Diamond City Market in shipments of 50.
  3. Sold by Rufus Rubins in Goodneighbor in shipments of 25.

How do you build a recruitment Radio Beacon?

Once it is safe, you’ll need to create a radio beacon in the Workshop found in the small shack. After you create a beacon and a generator, you’ll need to attach a wire to get the beacon working. To do this, remain in Workshop mode and look for the “Attach Wire” option when highlighting the generator.

How do you connect something to a generator in Fallout 4?

Published on Jan 9, 2016
  1. Build a Generator.
  2. Build a Switch.
  3. Select a built Switch in workshop and press “space” to attach wire to generator. Connect Switch and Generator.
  4. Confirm your attaching, press “space”.
  5. Build a Lightbulb.
  6. Enjoy!

How do I build a generator in Fallout 4?

To provide power to items like lights, fans, and even water purifiers, you must first begin by building a generator. Select a generator from the first tab of the Power section in the Workshop and decide where to place it. There are several types of generators, ranging in power output and resource cost.

How do you reconfigure the transmitter in Fallout 4?

Approach the Radio Equipment Slot, and install each radio part that you took from the crate. Note that you must insert the parts in a particular order to increase the transmitter’s power charge, indicated by the green lights on the transmitter. Install the parts in this order: buttons, dials, then tubes.

What do relay towers do in Fallout 4?

Scattered throughout the commonwealth are a series of relay towers which are marked by a tower with sparks coming off of it on your map. These towers have a computer at the base that allows for you to activate each relay station which will then begin to broadcast nearby signals to your pipboy.

How do you power up the signal interceptor?

Use one Wire to connect two of the three Large Generators together. Place a Large Power Pylon close to the Large Generators. Run a Wire from one of the two linked Large Generators to the Large Power Pylon. Connect that Large Power Pylon to the Beam Emitter with a single Wire.

How do you power up a radio beacon in Fallout 4?

Once it is safe, you’ll need to create a radio beacon in the Workshop found in the small shack. After you create a beacon and a generator, you’ll need to attach a wire to get the beacon working. To do this, remain in Workshop mode and look for the “Attach Wire” option when highlighting the generator.

How do you power up the transporter in Fallout 4?

Power up the Signal Interceptor
  1. Place the Reflector Platform.
  2. Snap the Beam Emitter to the Reflector Platform.
  3. Place the Relay Dish.
  4. Build and Place the Console.
People Also Asked :   What are the 3 stages to become a knight?

Do I need a recruitment beacon at the castle?

1 Answer. No, it doesn’t work as a recruitment beacon. The castle radio will unlock To recruit additional settlers you’ll have to construct the Recruitment Beacon just as you would for any other settlement, at which point you’ll pick up the Settlement Recruitment Beacon station.

How do you find copper in Fallout 4?

Locations
  1. Copper can be found all across the Commonwealth.
  2. A large number of junk objects containing copper can be found at Wattz Consumer Electronics.
  3. A large number of pre-War lamps (4 copper each) can be found at the Cabot House.
  4. Can also be scrapped from the street lamps in Sanctuary.